Skip to main content

DSLR Flash Not Firing

Why your flash may not fire when using a DSLR or mirrorless camera with Snappic, and how to fix it.

Written by Damir

Snappic doesn't control your flash. When you take a photo, Snappic only sends the shutter command to the camera. The camera then fires the flash through the hot shoe or sync port. That means almost every flash problem comes down to camera, flash or connection settings.


Important Notes

  • Always test your flash on the camera itself before connecting it to Snappic.

  • Flash settings, Silent LV Shoot and focus modes are changed on the camera. Snappic can't change them.

  • The built-in camera flash, Canon-branded flashes (such as the Speedlite range) and Canon-compatible third-party flashes are the most reliable. Some other third-party flashes may not fire, or may fire inconsistently.


Step 1: Test the Flash Outside Snappic

  1. Disconnect the camera from your iPad or iPhone.

  2. Press the camera's shutter button and check whether the flash fires.

  • It fires: the flash works. Reconnect to Snappic and see the sections below, starting with Live Preview and focus.

  • It doesn't fire: the problem is in the camera or flash setup. See "The flash doesn't fire at all" below.


Troubleshooting

Tap a section to open it.

The flash doesn't fire while Live Preview is on

Some cameras won't fire a flash while the live preview is active. This is most common on Nikon cameras, and can also happen on some other cameras and third-party flashes.

To fix this, turn off Live Preview in the DSLR settings in the Snappic app (under General).

Canon: turn off Silent LV Shoot

On some Canon DSLRs, the Silent LV (Live View) Shoot setting stops the flash from firing. Turning it off often fixes flash problems when connected to Snappic.

  1. Open the camera's main menu.

  2. Find Silent LV Shoot (usually under Live View or Custom Functions).

  3. Set it to Disable.

Not every camera has this setting. If yours doesn't:

  • Check whether Canon has a firmware update for your camera.

  • If the problem continues, you may need a different flash or a camera model that supports firing the flash with live view on.

The flash doesn't fire at all

Check

What to do

Flash settings

Make sure flash firing is enabled in the camera menu. On most Canon cameras, press the flash button (to the right of SET on newer models) or go to Flash Control.

Flash power and mode

Make sure the flash isn't in a low-power or wireless/slave mode. Some third-party flashes default to power-saving modes that stop them firing.

Hot shoe or sync connection

Check the flash is fully seated in the hot shoe and the contacts are clean. A loose or dirty contact stops the flash firing.

Flash batteries

Use fresh or fully charged batteries. Low power causes misfires.

Silent LV Shoot

Turn it off if your camera has it (see the section above).

Firmware

Update the camera and flash firmware.

The flash only fires sometimes

  • Check the flash mode and settings on the camera.

  • Check the sync cable or wireless trigger connection.

  • Check the flash batteries and charge level.

  • Set the camera to manual focus and test again. Sometimes autofocus stops the flash from firing.

  • If the flash fires when you press the camera's shutter button but not from Snappic, check the camera's USB connection setting. It should be set for remote control (for example, Photo Import / Remote Control on Canon), not image transfer only.


Quick Reference

Problem

What to do

Flash doesn't fire in Snappic

Disconnect the camera and test the flash on the camera

Flash doesn't fire on the camera either

Check the camera's flash setting is enabled

Flash fires only sometimes

Clean the hot shoe contacts, check power, try manual focus

Flash doesn't fire with live view on

Nikon: turn off Live Preview in Snappic. Canon: turn off Silent LV Shoot.

Flash not compatible

Try a Canon or Canon-compatible flash


Need Help? Contact Support

If your flash still isn't firing, send us a message in the chat with your camera model, flash model and a photo of your setup, and we'll help you troubleshoot.

Chat directly from your dashboard for live support


Related Articles

Did this answer your question?