Skip to main content

DSLR White Balance & Colour

Get natural colours from your DSLR in Snappic using white balance presets, Kelvin colour temperature or custom white balance.

Written by Damir

White balance (WB) tells the camera what colour the light is, so whites look white and skin tones look natural. Different lights (daylight, bulbs, LEDs) have different colour temperatures, measured in Kelvin (K). If white balance is wrong, photos look too warm (orange or yellow) or too cool (blue).


Important Notes

  • In Snappic you can choose a white balance preset or the Color Temperature (Kelvin) option. The Kelvin value itself is set on the camera.

  • For booths with controlled lighting, Kelvin or a preset gives more consistent colours than Auto White Balance.

  • Always check the colours by eye in the Snappic live view and the final photos.


White Balance Options

Tap a section to open it.

Auto White Balance (AWB)

AWB lets the camera choose the colour temperature for you. It's convenient, but it struggles with mixed lighting (for example LEDs plus daylight), which can cause uneven skin tones or colours that change from shot to shot.

Recommendation: only use AWB in steady, neutral lighting. For booth setups, use a preset or Kelvin instead.

White balance presets

You can choose a preset from the camera settings in the Snappic app:

Preset

About

Best for

Notes

Daylight

5200–5600 K

Outdoors or daylight-balanced lighting

Natural tones in sunlight or under daylight LED panels

Shade

7000 K

Outdoor shade, cloudy days

Warms up cool, blue light

Cloudy

6000 K

Overcast light or soft white LEDs

Slightly warmer; between daylight and shade

Tungsten

3200 K

Warm indoor bulbs

Removes the orange-yellow tint

Fluorescent

4000–4500 K

Office or fluorescent lighting

Removes the green tint from older tubes

Flash

5500–6000 K

Studio flashes or strobes

Neutral skin tones with flash

Custom WB

You set it

Mixed or complex lighting

Uses a grey or white card; most precise but rarely needed

Kelvin colour temperature (recommended)

For full control, use the Color Temperature option and set an exact Kelvin value on the camera, usually in steps of 500 K.

  1. In the Snappic app, select Color Temperature.

  2. On the camera, go to WB → K.

  3. Adjust in 500 K steps until the live preview looks natural.

  4. Check the live view and the final photos. Colours can look different depending on the booth lighting, even when the number is right.

Starting points:

  • 3200 K for warm tungsten bulbs

  • 5600 K for daylight or daylight-balanced LEDs

  • 6000–7000 K for cloudy or shaded light

Custom white balance (advanced)

You won't need this in most cases. The Color Temperature option above gives you more control. Use custom white balance only for very mixed lighting or when colour accuracy is critical.

  1. Place a neutral grey or white card where guests will stand.

  2. Take a photo of the card under the booth lighting.

  3. In the camera's Custom WB menu, choose that photo as the reference.

Custom white balance is set on the camera. Snappic doesn't change it.


Best Practices

  • Use Kelvin in controlled setups. It's the most reliable and repeatable.

  • Avoid AWB in mixed lighting.

  • Use custom WB only when lighting is very mixed or colour accuracy is critical.

  • For booths with flash, start with the Flash preset (about 5500 K) for neutral skin tones.

  • Always check results by eye in Snappic, not just the numbers.


Quick Fixes

Problem

Likely cause

What to do

Photos too orange or yellow

WB set too low (under 4000 K)

Raise the Kelvin value towards 5000–5600 K

Photos too blue

WB set too high (over 6000 K)

Lower the Kelvin value

Colours change between shots

AWB in mixed lighting

Switch to Kelvin or a preset in Snappic


Need Help? Contact Support

Colours still not right? Send us a message in the chat with your camera model, a sample photo and a photo of your booth lighting, and we'll help.

Chat directly from your dashboard for live support


Related Articles

Did this answer your question?